Course catalogue

This course aims to give offshore personnel a greater understanding of the hazards associated with packaging and cargo handling and the movement of cargo to, and from, offshore installations.

Course Content
-Explain the responsibilities and duties of all personnel and their duties under current legislation
-Explain the importance of checking for dropped objects and identify the areas that should be monitored
-Explain the key areas of safe lifting and slinging operations
-Explain the key principal points to be considered when preparing cargo for shipment to and from offshore
locations
-Describe the procedures involved for shipping freight by air
-Define what is classified as ‘Dangerous Goods by Sea’ and the main considerations for shipping
-Define what is classified as ‘Dangerous Goods by Air’ and the main considerations for shipping
-Explain the principal requirements for waste management
-Identify examples of bad practice

Fall protection is a course on the basics of fall protection for anyone working above ground.

This course outlines the laws and regulations related to fall protection. It contains information about active as well as passive protection gear, as well as first aid related to falls from a height. Upon completion of the course one will have information about the various aspects of fall protection. One will also learn how to carry out ones work in a safe and secure manner within the confines of the applicable laws and regulations.

Who is this course for?

Personnel requiring an awareness and understanding of hazardous substances risks and controls.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course provides learners with an awareness of working with hazardous substances

How will this course benefit my company?

By ensuring you are aware of working with hazardous substances so you can assist and inform best practice in your organisation.

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

This course aims to enhance the capabilities of shipboard personnel who sail on ships using LFF (low flashpoint fuel) as propulsion energy. It focuses on the responsibilities of all personnel serving on these kinds of ships. The course is developed in accordance with IMO model course 7:13.

1st January 2017 the IGF Code was made mandatory and STCW now includes new minimum requirements for the training and qualifications of personnel on ships subject to the IGF Code. This training program has been approved by the Norwegian Maritime Authority. The training consists of an e-learning course, practical assessment at a facility center and a classroom exam. When the training is completed a course diploma is issued. 

The practical training takes place at facilities located in various parts of Norway and abroad. Please choose the most convenient training for yourself or your employees. It is possible for our instructors to perform the practical assessment on the premises of a client. Should this be of interest please contact us on: post@gassteknikk.no

Who is this course for?

All employees at all levels of the organisation.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

Insufficient understanding of risk often leads to delayed projects, accidents and other unwanted incidents.

This course provides a basic understanding of what risk is, how it can be managed and how understanding risk helps us make better decisions.

How will this course benefit my company?

By ensuring you are aware and have a basic understanding of what risk is and how to manage risk. 

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

Is there an assessment?

There is no exam upon completion of this course.

The main objective of the course in pressure testing is to provide each course participant the basic knowledge of the preparation, planning, execution and documentation of pressure testing as a discipline.

Focus on safety and proper selection of equipment is essential to prevent accidents and loss of assets.

Training will be made according to specific standards. The course will include a theoretical part, practical part and examinations.

Course Content

Theoretical part

The main tasks during the course will be:

- Different methods for pressure testing

- Performance of pressure testing

- Work Packages and drawings

- HSE

- Equipment for pressure testing

- Pressure and temperature theory

- Introduction in fittings and thread types

- Flanges, Gaskets and Bolts

- Valves

- Standards, calibration and documentation

Practice

The simulated practice test will be performed on a training jig under supervision of an instructor. There will be reviewed work packages for performing virtually work packages which will be out in the field.

Who is this course for?

Personnel such as processors or trainee processors requiring awareness or understanding of the various process safety systems.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to provide learners with an overview of the various process safety systems that are employed in the Oil and Gas Industry.

How will this course benefit my company?

By ensuring you have an overview of the process of the various process safety systems that are employed in the Oil and Gas Industry.

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?

Personnel requiring an understanding & awareness of the role of a fire warden or have recently been allocated this role or require a refresher.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to provide Fire Wardens with an overview of the knowledge that they need to carry out their duties safely and effectively in line with industry best practice

How will this course benefit my company?

By ensuring you have the knowledge needed to carry out  duties safely and effectively in line with industry best practice

What standards are referred to in this course?

Health and Safety at Work Act

The Fire (Scotland) Act

The Regulatory Reform (Fire Safety) Order

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?

This FSE High and Low Voltage Training course is suitable for everyone working on low and high voltage installations.

Is previous experience required?

You do not need prior knowledge or experience to complete this course, but it is assumed that you are competent in your designated role.

How will this course benefit me?

The course meets the requirements set in Section 7 of the ‘Safety Regulations for Work and Operation of Electrical Equipment and Installations – FSE’ which is that all relevant personnel undertake annual training and instruction in FSE. The course also provides the necessary training and instruction in first aid, focusing on electrical injuries, with the exception of the mandatory practical training in cardiopulmonary resuscitation (CPR).

The regulations of various authorities make FSE applicable to all those working with electricity, whether on board ship, on platforms or on land. This course is suitable for all, regardless of which industry you work in.

The authorities require that training in FSE and first aid in the event of electrical accidents is undertaken at least once a year. No more than 12 months shall elapse between training courses.

How will this course benefit my company?

By ensuring you have the knowledge and competence to be working on low and high voltage installations.

What standards are referred to in this course?

• Section 7 of the ‘Safety Regulations for Work and Operation of Electrical Equipment and Installations – FSE’

• The European standard

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course Goal:

This course provides learners with an awareness of US best practice in relation to working at height and fall protection.

Learning Objectives:

LO1 Identify when fall protection is required

LO2 Identify the legislative and regulatory requirements for fall protection that help to control work at height

LO3 Explain the duties that are placed on employers and employees

LO4 Describe the hazards involved in working at height

LO5 Explain the importance of planning and risk assessment

LO6 Describe the hierarchy of control for managing and selecting fall protection equipment 

LO7 Identify the factors that should be considered when assessing fall protection methods

LO8 Describe the main methods of access for working at height and give examples of the different types of fall protection equipment

LO9 Describe the rules for working with ladders

LO10 Describe the rules for working with scaffolds

LO11 Explain the importance of inspecting equipment

LO12 Explain how to correctly use a safety harness

Who is this course for?

This course is aimed at all personnel involved in mechanical joint operations, particularly those who are expected to undertake related duties in the workplace.

Is previous experience required?

You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?

This course aims to provide learners with an introduction to the principles of the equipment and technology associated with the bolting of flanged joints for pressurised systems. This course is intended to reflect industry """"best practice"""" for competence in relation to mechanical joint operations and applies to both the onshore and offshore Oil and Gas Industry.

This course contains the following sections:

Section 1: An Introduction to Mechanical Joint Integrity

Section 2: Principles of Hand Torquing

Section 3: Principles of Hydraulic Tensioning

Section 4: Principles of Controlling Tightening

How will this course benefit my company?

By ensuring you are introduced  to the  principles of the equipment and technology associated with the bolting of flanged joints for pressurised systems

What standards are referred to in this course?

N/A

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course Goal:

This course aims to provide learners of an awareness of US best practice in relation to confined space entry (CSE), hazardous atmospheres, and the necessary equipment, and permits required to work in confined spaces.

It will also examine the hazards and hazard control methods that are required to undertake work safely in a confined space and the actions that should be taken in an emergency.

Learning Objectives

LO1  Explain what is meant by a Confined Space

LO2  Give examples of Confined Spaces

LO3 Describe the dangers that can be caused by confined space entry work 

LO4 Identify OSHA requirements for permit-required entry operations

LO5 Explain how to avoid entering confined spaces

LO6 Explain the importance of having a Safe System of Work in place

LO7 Describe individual roles and responsibilities involved in Confined Space Entry work 

LO8 Explain the requirements for gas testing

LO9 Identify acceptable levels for atmospheric test results 

LO10  Give examples of Confined Space Entry site safety equipment

LO11  Explain the actions to take in an emergency 

LO12  Explain Confined Space Entry alarm procedures

Who is this course for?

Personnel who are required to work with Piping and Instrumentation Diagrams.

Is previous experience required?

No previous experience is required to complete this course.

How will this course benefit me?

This course will enable you to describe the information provided in a P&ID and explain why this information is useful.

How will this course benefit my company?

Personnel who are able read and understand the information provided in P&IDs are better able to troubleshoot system problems.

What standards are referred to in this course?

• Institute de Algerian Normalisation

• Standards Association of Zimbabwe

Is there an assessment?

Once you have completed each section of the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the section and have a pass mark of 80%.

Who is this course for?

All personnel who work with chemicals in the Oil and Gas Industry.

Is previous experience required?

No previous experience is required to complete this course.

How will this course benefit me?

This course provides learners with an in depth few on the use, management and control of chemicals in the Oil and Gas Industry and how to react in an emergency situation that has resulted from a chemical hazard.

How will this course benefit my company?

The course will benefit companies by ensuring that all personnel have an in depth view of industry best practice for working with chemicals, which will in turn, help keep those working with chemicals safe.

What standards are referred to in this course?

• The Control of Substances Hazardous to Health (COSHH)

• The Offshore Chemicals (Amendment) Regulations

• The Offshore Chemicals Regulations (OCR)

• Offshore Petroleum (Oil Pollution Prevention and Control) Regulations

• Regulation, Evaluation, Authorisation and restriction of Chemicals  (REACH)

• Occupational Safety and Health Administration (OSHA)

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?

Any personnel who require an awareness of human factors.

Is previous experience required?

No previous experience is required to complete this course.

How will this course benefit me?

This course aims to introduce learners to the concept of human factors and how they impact situational awareness.

How will this course benefit my company?

The course will benefit companies by ensuring that all personnel have an understanding of the human factors that can affect their situational awareness, resulting in reduced accidents and injuries.

What standards are referred to in this course?

No standards or regulations are referenced in this course.

Is there an assessment?

No

This course provides an introduction to emergency first aid. After completing the course, users will feel secure enough in their knowledge to be able to take action in an accident situation by analyzing the situation and understanding the order in which to do what needs to be done.

Course Content

- Introduction

- Lifesaving first aid
- To call for help
- The important survey
- Stroke
- Cardiac Resuscitation
- Heart Disease
- Internal and external bleeding

Who is the course for?

All personnel working within the Oil and Gas Industry (onshore and offshore).

Is previous experience required?

You do not require previous experience to complete this course.

How will the course benefit me?

This course will provide you a basic understanding the ways in which industrial operations can impact the environment and the steps that we can all take to minimise these impacts.

How will the course benefit my company?

Environmentally aware personnel can help to reduce the environmental impacts of your operations and improve environmental performance.

What standards are referenced in the course?

ISO 14001 Environmental Management Systems

Offshore Chemical Regulations

Integrated Pollution Prevention and Control (IPPC) Directive

Control of Major Accident Hazards (COMAH) Regulations

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Course Goal:

This course aims to increase the learner's awareness of US best practice in relation to Personal Protective Equipment (PPE), and outline the responsibilities of employers and personnel in relation to PPE.

Learning Objectives

Section 1: The Importance of PPE

LO1 Define what is meant by Personal Protective Equipment (PPE)

LO2 Identify the regulations surrounding the use of PPE

LO3 Describe the Hierarchy of Control measures

LO4 Describe the duties and responsibilities of employers in relation to PPE

LO5 Explain the importance of PPE-related training, information and instruction 

LO6 Describe the responsibilities of personnel in relation to PPE

Section 2: Types of PPE

LO7 Identify the different types of PPE 

LO8 Describe how to select, use and maintain different types of PPE

Section 3: PPE Requirements

LO9 Identify different types of Respiratory Protective Equipment (RPE)

LO10 Explain the requirements for face fit testing

LO11 Explain the requirements for the use of fall protection

LO12 Explain the requirements for assessing the suitability and compatibility of PPE

LO13 Describe the four levels of PPE protection

LO14 Explain the importance of proper donning and doffing techniques

Who is this course for?

Personnel requiring an awareness or understanding of the role of Banksmen and Slingers.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to give an overview of the roles of the Banksman and Slinger

How will this course benefit my company?

To ensure you have an overview of the roles of the Banksman and Slinger

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?
Deck Officers and Deck Crew.

Is previous experience required?
You do not need prior knowledge or experience to complete this course.

How will this course benefit me?
This course aims to provide learners with an introduction to Emergency Towing Systems (ETS) in the Maritime Industry.

How will this course benefit my company?
By ensuring you have an understanding of the Emergency Towing Systems.

What standards are referred to in this course?
N/A

Is there an assessment?
Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 70%.