Course catalogue

The course is a management support and provides an introduction to Risk assessment, HSE regulations and Training requirements. The course is also helpful for everyone involved in the training of hazardous work equipment.
The course is intended to give participants an introduction to the HSE regulations, and requirements for training, especially relating to dangerous tools.

The course provides knowledge about the structure, operation, applications and usage, maintenance and monitoring of the appropriate tool. The training provides knowledge about the requirements for safe use and operation stipulated in regulations and instructions.

Along with a practical review of the tools, the course meets the requirements for documented training in hazardous work equipment in Regulations concerning the Performance of Work.

The course covers the following subjects:

- Introduction to general HSE
- Angle grinder
- Hammer drills, jackhammers and combihammers
- Powder actuated gun
- Nail gun
- Saws with blade (includes table saw, crosscut and miter Saw, circular saw, jigsaw and reciprocating saw)
- Chain saw

Requirements for training related to scaffolding are regulated by law and regulations. This course is based on the requirements of Regulations concerning the Performance of Work, Chapter 17, which is about assembly, dismantling and alteration of scaffolding.

-2-5 meters: 7.5 hours theory and  7.5 hours practical training
-5-9 meters: 15 hours theory and 15 hours practical training
-Over 9 meters: 36 hours theory and 72 hours practical training

This course covers the requirements of theoretical training for scaffolding up to 9 meters, and corresponds to the requirements of the Regulations concerning the Performance of Work, Section 17-2 and 17-3, on theoretical training. There is an additional requirement of 15 hours practical training if 5-9 meters. 

Course content:
-What is scaffolding
-Scaffolding and safety
-Risk assessment
-Forces and counter forces
-Structure of a scaffold
-Wind forces
-How to prevent accidents
-Mobile scaffold towers
-Haki scaffolding systems

Dersom du har gjennomført stillasopplæring (teorikurs) - og kan dokumentere nødvendig praksis i henhold til kravene i forskrift om utførelse av arbeid §§17-2, 17-3 og 17-4 - kan du bestille stillasbevis.

Klikk her for informasjon: https://www.eba.no/stillasbevis/

Du må ha gjennomført stillaskurs del 1 før dette kurset. 

Dette kurset er bygget på krav i Forskrift om utførelse av arbeid, kapittel 17, som omhandler montering, demontering og endring av stillas.
Forskriften krever opplæring for ulike stillashøyder:
-2-5 meter: 7,5 timer teori og 7,5 timer praksis
-5-9 meter: 15 timer teori og 15 timer praksis
-Over 9 meter: 36 timer teori og 72 timer praksis.

Dette kurset forutsetter at du har gjennomført stillaskurs del1. Til sammen dekker disse kursene kravene til teoretisk opplæring for stillas over til 9 meter, og tilsvarer kravene i Forskrift om utførelse av arbeid § 17-2 -17-4 om teoretisk opplæring.
I tillegg er det krav om 72 timer praktisk opplæring under tilsyn av kvalifisert person, ref Forskrift om utførelse av arbeid § 17-2 - 17-4.

Kursinnhold:
-Innledning
-Risiko ved arbeid i høyden
-Montering, endring og demontering
-Rør og kobling
-Vindkrefter, beregning for vindkrefter og forankring
-Sikkert arbeid i høyden, risikovurdering og fallsikring
-Diverse stillaskonstruksjoner
-Beregninger

Dersom du har gjennomført stillasopplæring (teorikurs) - og kan dokumentere nødvendig praksis i henhold til kravene i forskrift om utførelse av arbeid §§17-2, 17-3 og 17-4 - kan du bestille stillasbevis.

Klikk her for informasjon: https://www.eba.no/stillasbevis/

Requirements for training related to scaffolding are regulated by law and regulations. This course is based on the requirements of Regulations concerning the Performance of Work, Chapter 17, which is about assembly, dismantling and alteration of scaffolding.

-2-5 meters: 7.5 hours theory and  7.5 hours practical training

-5-9 meters: 15 hours theory and 15 hours practical training

-Over 9 meters: 36 hours theory and 72 hours practical training

This course covers the requirements of theoretical training for scaffolding up to 9 meters, and corresponds to the requirements of the Regulations concerning the Performance of Work, Section 17-2 and 17-3, on theoretical training. There is an additional requirement of 15 hours practical training if 5-9 meters.

Course content:
-What is scaffolding
-Scaffolding and safety
-Risk assessment
-Forces and counter forces
-Structure of a scaffold
-Wind forces
-How to prevent accidents
-Mobile scaffold towers
-Haki scaffolding systems

Dersom du har gjennomført stillasopplæring (teorikurs) - og kan dokumentere nødvendig praksis i henhold til kravene i forskrift om utførelse av arbeid §§17-2, 17-3 og 17-4 - kan du bestille stillasbevis.

Klikk her for informasjon: https://www.eba.no/stillasbevis//