Course catalogue

Requirements for training related to scaffolding are regulated by law and regulations. This course is based on the requirements of Regulations concerning the Performance of Work, Chapter 17, which is about assembly, dismantling and alteration of scaffolding.

-2-5 meters: 7.5 hours theory and  7.5 hours practical training
-5-9 meters: 15 hours theory and 15 hours practical training
-Over 9 meters: 36 hours theory and 72 hours practical training

This course covers the requirements of theoretical training for scaffolding up to 9 meters, and corresponds to the requirements of the Regulations concerning the Performance of Work, Section 17-2 and 17-3, on theoretical training. There is an additional requirement of 15 hours practical training if 5-9 meters. 

Course content:
-What is scaffolding
-Scaffolding and safety
-Risk assessment
-Forces and counter forces
-Structure of a scaffold
-Wind forces
-How to prevent accidents
-Mobile scaffold towers
-Haki scaffolding systems

Dersom du har gjennomført stillasopplæring (teorikurs) - og kan dokumentere nødvendig praksis i henhold til kravene i forskrift om utførelse av arbeid §§17-2, 17-3 og 17-4 - kan du bestille stillasbevis.

Klikk her for informasjon: https://www.eba.no/stillasbevis/

Du må ha gjennomført stillaskurs del 1 før dette kurset. 

Dette kurset er bygget på krav i Forskrift om utførelse av arbeid, kapittel 17, som omhandler montering, demontering og endring av stillas.
Forskriften krever opplæring for ulike stillashøyder:
-2-5 meter: 7,5 timer teori og 7,5 timer praksis
-5-9 meter: 15 timer teori og 15 timer praksis
-Over 9 meter: 36 timer teori og 72 timer praksis.

Dette kurset forutsetter at du har gjennomført stillaskurs del1. Til sammen dekker disse kursene kravene til teoretisk opplæring for stillas over til 9 meter, og tilsvarer kravene i Forskrift om utførelse av arbeid § 17-2 -17-4 om teoretisk opplæring.
I tillegg er det krav om 72 timer praktisk opplæring under tilsyn av kvalifisert person, ref Forskrift om utførelse av arbeid § 17-2 - 17-4.

Kursinnhold:
-Innledning
-Risiko ved arbeid i høyden
-Montering, endring og demontering
-Rør og kobling
-Vindkrefter, beregning for vindkrefter og forankring
-Sikkert arbeid i høyden, risikovurdering og fallsikring
-Diverse stillaskonstruksjoner
-Beregninger

Dersom du har gjennomført stillasopplæring (teorikurs) - og kan dokumentere nødvendig praksis i henhold til kravene i forskrift om utførelse av arbeid §§17-2, 17-3 og 17-4 - kan du bestille stillasbevis.

Klikk her for informasjon: https://www.eba.no/stillasbevis/

The course covers the following topics:

- Which companies should have a Working Environment Committee (AMU)?
- How to organize the a Working Environment Committee (AMU)?
- What is a Working Environment Committee (AMU)?

At the beginning of the course you can take a pre-test, where you get the opportunity to show your skills. If you pass the pre-test, you do not have to go through the entire course.

The object of this course is to provide participants with basic knowledge and skills regarding helicopter operations, for both normal and emergency operations on the helideck, including safety routines and accident prevention. Participants also receive training on the relevant fire, rescue and protective equipment found on the helideck.

Course Content

- Laws and regulations

- Weather reporting, communication and routines

- Helideck regulations and guidelines

- Dangerous cargo

- Aviation fuel

- The responsibilities and tasks of the helideck crew during emergencies and abnormal operations

- The responsibilities and tasks of the helideck crew during normal operations

- Human factors

- Types of helicopters

- Fire theory

- The different extinguishing agents and their use

- Practice in fire fighting at a safety centre/school

This course is valid for 24 months.

Who is this course for?

Personnel who require a basic understanding of the operation of diesel engines and the importance of maintaining good lubrication for their safe operation.

Is previous experience required?

No previous experience is required to complete this course.

How will this course benefit me?

This course will provide you with an overview of how diesel engines operate, their components and their use within the industry. It will also outline the importance of maintaining good lubrication for their safe operation.

How will this course benefit my company?

This course will provide personnel with an overview of how diesel engines operate and the importance of maintaining good lubrication for their safe operation.

What standards are referred to in this course?

This course does not refer to specific legislation or standards.

Is there an assessment? 

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

The object of this course is to help course participants maintain and develop their knowledge, skills and attitudes regarding their role in an emergency response situation.

Who is this course for?
All relevant personnel.

Is previous experience required?
You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?
This course aims to provide personnel with an overview of how the Working Time Regulations impact on their working hours and the importance of effectively managing and assess the risks posed by fatigue in the workplace.

How will this course benefit my company?
By ensuring you have an overview of how the Working Time Regulations impact on their working hours and the importance of effectively managing and assess the risks posed by fatigue in the workplace.

What standards are referred to in this course?
N/A

Is there an assessment?
Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Presentation

This training course provides a general introduction to the corrosion process, the protective coating used to prevent corrosion, the coating process and coating inspection.

Objectives

On completion of the training, students will be able to:

Know the different types of corrosion and their causes.

Understand the corrosion phenomenon and the threat it represents to the structural integrity.

Know the protective coating systems used in shipbuilding.

Be familiar with the constituents, structure and curing prerequisites of the protective coating systems.

Understand the different phases of the coating process and the requirements for successful coating application.

Be familiar with coating inspection procedures and the requirements of the IMO PSPC.

Recognise the different forms of coating failure.

Program

Module 1 - Introduction to Corrosion and Protective Coatings

Corrosion definition

Causes of corrosion

Different forms of corrosion

Corrosion rate

Protective coating systems

Paint coating components

Types of coatings

Technical data sheets

Coating cure

Module 2 - Coating Process and Inspection

Coating process scheme

Surface preparation

Cleaning techniques

Surface preparation

Paint application

Coating durability requirements

Coating inspection

Coating system documentation

Coating inspector qualifications

Inspection procedures and plan

Coating defects

Certificate

On completion of the training program, the student will be awarded the following qualifications:

Certificate of Corrosion and Coating awarded by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Corrosion and Coating, issued by Bureau Veritas Solutions Marine & Offshore, is obtained after completing the course and passing the qualification examination.

Presentation

This training course is about what an effective cyber security risk management should be. Its goal is not to address too many technical questions as the best technical expertise in the world won’t guarantee zero cyber risk. The course aims at providing your Company with a real battle plan: know the assets, know the enemies, organize accordingly and train the effectives. Although this will not be enough to avoid a cyber incident, the severity of the consequences of a cyber incident will depend on the company’s preparedness and ability to manage it.

Who the course is for?

The course ISM Code and Cyber Risk Management is aimed at anyone interested in understanding how an effective cyber security risk management should be. This may include Top Management of Shipping Companies, Ship Managers, Technical Superintendents, Ship Masters, Officers and Seafarers; Offshore Units Operators and Technical Staff, Shipyards Technical Staff; Surveyors; P&I and/or Insurance Inspectors; etc.

Objectives

On completion of the training, students will be able to:

Know what cyber security is, the main threats and their consequences.

Understand how to consider the cyber risks in the Safety Management System and how the ISM Code translated into cyber security.

Know the 12 cybersecurity commandments that will help implementing an efficient cyber risk management system.

Who is this course for:
Anyone wanting to take the SRC/VHR-exam.

Is previous experience required?
You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?
To use VHF you must have a VHF / SRC certificate. With this course you will learn the whole curriculum in a simple and easily understandable way.

How will this course benefit my company?
By ensuring you have the competence to use VHF.

What standards are referred to in this course?
Lovdata - www.lovdata.no
Petroleum Safety Authority - www.psa.no

Is there an assessment?
Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

This course aims to give personnel the knowledge required to understand the hazards and controls associated with noise in the workplace.

Course Content

LO1 Describe what noise-induced hearing loss is, and identify the early warning signs and symptoms to look out for

LO2 Explain the workings of the human ear, how noise exposure causes damage, and the effects of such damage

LO3 Explain the responsibilities and duties of employers and employees under current legislation

LO4 Explain how noise is measured and identify the noise levels above which employers should take action to reduce exposure

LO5 Explain the risk assessment requirements

LO6 Identify the control measures that should be taken to reduce exposure to noise

LO7 Explain the requirements for hearing protection; how to use the different methods of hearing protection and the importance of maintaining hearing protection

LO8 Explain the importance of healthsurveillance

The course for you that must issue a work certificate according to the Norwegian Labor Authority’s regulations nr 1357 “Regulations for execution of work», and is to be registered as a Gas tester offshore or in ship yard, chemical or petro-chemical plants.

Content:

HES – datasheets and physical/chemical terms.Fire and explosion theory with practical demonstrations.Measuring principle, function and limitations for: sensors for flammable gas, oxygen and hazardous substances.Regulations and guidelines.Operation and use of gas measuring instruments.Quality control of equipment and personnel.LRA (low radioactive deposition)Measuring methods benzene.Dangers of static electricityZone classificationGas freeing and cleaning methodsDangers of H2S and benzene exposurePreparations for safe entry and correct use of protective equipment.Work permits and safe job analysis (WP/SJA)Group tasks: Develop plan for nitrogen purging, valve and blinding plan according to procedure for preparations before and after maintenance. Gas freeing: Practical group task in our mobile course container (miniature process facility).Practical and written exam

Who is this course for?

This course is aimed at all personnel involved in operations involving the use of seals, particularly those who are expected to undertake related duties in the workplace.

Is previous experience required?

You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role.

How will this course benefit me?

This course aims to provide an overview of the role and application of seals and gaskets.

How will this course benefit my company?

To ensure you have an overview of the role and application of seals and gaskets.

What standards are referred to in this course?

The course is made according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Who is this course for?

Personnel requiring awareness or understanding of subsea control systems.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to provide an overview of subsea control systems and has the following sections:

Section 1: Evolution of Subsea Technology

Section 2: Subsea Completions Layout

Section 3: Subsea Control Systems

Section 4: Subsea Process Control

Section 5: Subsea Technology Development

How will this course benefit my company?

By ensuring you have an overview of industry best practice in relation to Subsea Control Systems.

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

This course includes all subjects needed to prepare candidates for the rotary drilling well control exam, surface and subsea BOP stack on driller level (Level 3).

A printed course manual and exercise book is provided for all attendees. The IWCF exam is included in the course.

The course has been made on basis of the recommendations for enhancements to well control training, issued by the International Association of Oil & Gas Producers (OGP).

Course Content
- Kick prevention
- Shut in procedures
- Well control methods
- Kill sheet calculations
- Practical simulator training
- Circulation methods
- Practical simulator assessment
- IWCF written exam on the last day (Friday)

Please note! The course is in Norwegian, however you have the option to select the exam language to be English

The object of this course is to help participants maintain and develop their knowledge, skills and attitudes regarding their operational / emergency response function.

A representative selection of the content of the Small MOB Boat Basic Course adapted to participants’ previous knowledge, with major emphasis on practical training and drills.

This course is valid for 24 months.

Who is this course for?

Personnel requiring an awareness or understanding of (Material) Safety Data Sheets ((M)SDS) for chemicals.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to provide an overview of the structure and information contained in Safety Data Sheets.

How will this course benefit my company?

By ensuring you have an overview of Safety Data Sheets and how your role may require to understand certain information contained in the sheets.

What standards are referred to in this course?

Chemicals (Hazard Information and Packaging for Supply) Regulations 2009

CLP Regulation

REACH Regulation

Control of Substances Hazardous to Health (CoSHH) Regulations

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%. 

The course covers the following topics:

- Agreement on Inclusive Working Conditions
- Working environment and prevention
- Absence

At the beginning of the course you can take a pre-test, where you get the opportunity to show your skills. If you pass the pre-test, you do not have to go through the entire course.

Who is this course for?
Process Operators and Lab Technicians

Is previous experience required?
You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?
This course aims to provide an overview of the various types of process chemicals, their use and how they work.

Section 1: Basic Introduction to Chemistry
Section 2: Process Chemicals in the Oil and Gas Industry
Section 3: Identifying the Risks in the Use of Process Chemicals
Section 4: Managing Chemical usage

How will this course benefit my company?
By ensuring you have an overview of the various types of process chemicals, their use and how they work.

What standards are referred to in this course?
N/A

Is there an assessment?
Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

This course covers the theoretical part of the documented safety training required for slingers and signallers. The course is also suitable as a refresher for crane operators and other personnel who have previously completed training in lifting appliances and lifting gear. The course content deals with selection, control and safe use of the most common lifting gear used in construction, industry, shipping and offshore. Signalling, communication and controlling the load are key topics of the course.

In addition, the course requires that practical training is conducted on applicable work equipment.

The course contains 9 modules:

• Lifting equipment, expressions and acronyms

• Slinging, center of gravity, working angles and lifting tables

• Fibre slings

• Lifting gears of chain

• Wire rope slings

• Shackles

• Eye bolts, nuts and lifting lugs

• Signals and signs, and control of load

• Safety regulations for lifting operations