Kurskatalog

Course Goal: This course aims to provide learners with an overview of gas liquids and their chemical and physical properties. 

Learning Objectives:

Section 1: An Overview of Gas Liquids

Section 2: Chemical and Physical Properties of Gas Liquids

Section 3: Liquefied Petroleum Gas

Section 4: Natural Gas Liquids (NGL) Recovery

Section 5: Removal of Natural Gas Impurities

Section 6: Liquefaction of Natural Gas

Section 7: Shore-Based Storage of Gas Liquids

Section 8: Transportation of Liquefied Natural Gas

Section 9: Health, Safety and Environmental (HSE) Issues of Gas Liquids

Kurset er kun tilgjengelig på engelsk. 

Du må ha gjennomført Stillaskurs del 1 før dette kurset. 

Dette kurset er bygget på krav i Forskrift om utførelse av arbeid, kapittel 17, som omhandler montering, demontering og endring av stillas.
Forskriften krever opplæring for ulike stillashøyder:
-2-5 meter: 7,5 timer teori og 7,5 timer praksis
-5-9 meter: 15 timer teori og 15 timer praksis
-Over 9 meter: 36 timer teori og 72 timer praksis.

Dette kurset forutsetter at du har gjennomført stillaskurs del1. Til sammen dekker disse kursene kravene til teoretisk opplæring for stillas over 9 meter, og tilsvarer kravene i Forskrift om utførelse av arbeid § 17-2 -17-4 om teoretisk opplæring.
I tillegg er det krav om 72 timer praktisk opplæring under tilsyn av kvalifisert person, ref Forskrift om utførelse av arbeid § 17-2 - 17-4.

Kursinnhold:
-Innledning
-Risiko ved arbeid i høyden
-Montering, endring og demontering
-Rør og kobling
-Vindkrefter, beregning for vindkrefter og forankring
-Sikkert arbeid i høyden, risikovurdering og fallsikring
-Diverse stillaskonstruksjoner
-Beregninger

Dersom du har gjennomført stillasopplæring (teorikurs) - og kan dokumentere nødvendig praksis i henhold til kravene i forskrift om utførelse av arbeid §§17-2, 17-3 og 17-4 - kan du bestille stillasbevis.

Klikk her for informasjon: https://www.eba.no/stillasbevis/

Dette kurset er bygget på krav i Forskrift om utførelse av arbeid, kapittel 17, som omhandler montering, demontering og endring av stillas.

Forskriften krever opplæring for ulike stillashøyder:
-2-5 meter: 7,5 timer teori og 7,5 timer praksis
-5-9 meter: 15 timer teori og 15 timer praksis
-Over 9 meter: 36 timer teori og 72 timer praksis.

Dette kurset dekker kravene om teoretisk opplæring for stillas opp til 9 meter, og tilsvarer kravene i Forskrift om utførelse av arbeid § 17-2 og 17-3 om teoretisk opplæring. I tillegg er det krav om 15 timer praktisk opplæring under tilsyn av kvalifisert person hvis 5-9 meter.

Du kan bygge på med "Stillaskurs – del 2", som dekker stillas over 9 meter.

Kursinnhold:
-Hva er et stillas
-Sikkerhet og stillas
-Risikovurdering
-Krefter og motkrefter
-Stillasets oppbygging
-Vindkrefter
-Hvordan unngå ulykker
-Rullestillas
-Haki systemstillas

Dersom du har gjennomført stillasopplæring (teorikurs) - og kan dokumentere nødvendig praksis i henhold til kravene i forskrift om utførelse av arbeid §§17-2, 17-3 og 17-4 - kan du bestille stillasbevis.

Klikk her for informasjon: https://www.eba.no/stillasbevis/

Who is this course for?

Personnel who require a basic understanding of the operation of diesel engines and the importance of maintaining good lubrication for their safe operation.

Is previous experience required?

No previous experience is required to complete this course.

How will this course benefit me?

This course will provide you with an overview of how diesel engines operate, their components and their use within the industry. It will also outline the importance of maintaining good lubrication for their safe operation.

How will this course benefit my company?

This course will provide personnel with an overview of how diesel engines operate and the importance of maintaining good lubrication for their safe operation.

What standards are referred to in this course?

This course does not refer to specific legislation or standards.

Is there an assessment? 

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Kurset omhandler følgende emner:

- Hvilke bedrifter skal ha AMU?
- Hvordan organisere AMU?
- Hva gjør AMU?

I begynnelsen av kurset kan du ta en pre-test, hvor du får mulighet til å vise dine kunnskaper. Består du pre-testen, behøver du ikke gå gjennom hele kurset.

Course Goal: 

This course aims to familiarize learners with US best practice in relation to working with sealed sources of radiation, and measures that should be taken to protect personnel from radiation exposure.

Learning Objectives:

LO1 Define what is meant by ‘radioactive material’

LO2 Explain what is meant by the terms ‘sealed source’ and ‘unsealed source’

LO3 Give examples of sealed sources in the workplace

LO4 Identify the hazards associated with radiation

LO5 Identify the PPE requirements for handling radioactive materials

LO6 Give an overview of the exposure limits for handling radioactive materials 

LO7 Describe the correct method for performing personal monitoring

LO8 Explain how the hazards associated with radioactive materials can be mitigated

LO9 Identify control measures that should be taken to protect personnel from radiation exposure

LO10 Explain the actions to take in the event of an emergency 

Kurset er kun tilgjengelig på engelsk.

Presentation

This training course provides a general introduction to the corrosion process, the protective coating used to prevent corrosion, the coating process and coating inspection.

Objectives

On completion of the training, students will be able to:

Know the different types of corrosion and their causes.

Understand the corrosion phenomenon and the threat it represents to the structural integrity.

Know the protective coating systems used in shipbuilding.

Be familiar with the constituents, structure and curing prerequisites of the protective coating systems.

Understand the different phases of the coating process and the requirements for successful coating application.

Be familiar with coating inspection procedures and the requirements of the IMO PSPC.

Recognise the different forms of coating failure.

Program

Module 1 - Introduction to Corrosion and Protective Coatings

Corrosion definition

Causes of corrosion

Different forms of corrosion

Corrosion rate

Protective coating systems

Paint coating components

Types of coatings

Technical data sheets

Coating cure

Module 2 - Coating Process and Inspection

Coating process scheme

Surface preparation

Cleaning techniques

Surface preparation

Paint application

Coating durability requirements

Coating inspection

Coating system documentation

Coating inspector qualifications

Inspection procedures and plan

Coating defects

Certificate

On completion of the training program, the student will be awarded the following qualifications:

Certificate of Corrosion and Coating awarded by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Corrosion and Coating, issued by Bureau Veritas Solutions Marine & Offshore, is obtained after completing the course and passing the qualification examination.

Who is the course for?

This eLearning course is aimed at individuals who work offshore, in any role, anywhere in the world.

Is previous experience required?

The course is designed for existing workers in the oil and gas industry. Completion of this course awards an IMIST certificate valid for four years, after which you will need to sit the course again to refresh your knowledge and earn a new certificate.

How will the course benefit me?

The offshore working environment is home to many hazards, which means that it is vital for everyone who goes offshore to have the same baseline level of safety knowledge. This course has been created with OPITO to set a global safety standard by applying a consistent level of safety awareness across nine safety critical areas and is applicable.

The knowledge gained in this course will help you to stay safe in your day-to-day activities offshore. It will also outline some of the systems and procedures in place to manage everyday operations offshore.

How will the course benefit my company?

By ensuring that your safety knowledge is at or above the baseline level, your company can rest assured that you are able to work offshore safety and in compliance with regulations and company procedures. Increased safety knowledge helps to prevent incidents and makes your working environment a safer place.

What standards are referenced in the course?

This course is written based on the OPITO standard International Minimum Industry Safety Training Standard (IMIST) (5312). As a global standard, the course is not written to meet any specific regional legislation but references industry best practices and standard operating procedures throughout.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 100%. 

The course starts with an optional pre-assessment that checks your existing knowledge of the course topics. The course will restructure so that it only contains the content needed to address the gaps in your knowledge.

Who is the course for?

This course is aimed at individuals working in industrial sectors whose activities can impact the environment.

Is previous experience required?

You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role.

How will the course benefit me?

This course will give you a basic understanding of environmental ‘aspects’ and ‘impacts’ and explain the purpose of an Environmental Management System (EMS).

The knowledge gained in this course will help you to stay in compliance with legislative requirements. It will also explain how you can play your part in improving environmental performance.

How will the course benefit my company?

By ensuring you are fully aware of the role of ISO 14001 in environmental management, you contribute to continual improvement in environmental performance, as well as ensuring that you operate in compliance with relevant regulations and legislation.

What standards are referenced in the course?

ISO 14001

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Dette kurset er kun tilgjengelig på engelsk.

For å bruke maritim VHF må du ha VHF/SRC-sertifikatet. Med dette kurset lærer du deg hele pensum på en enkel og lettfattelig måte.

Kurset inneholder følgende emner:
- Om VHF
- VHF-apparatet
- Praktisk bruk av VHF (DSC)
- Nødradioutstyr og globale kommunikasjonssystemer
- Avslutning

NORSOK standard R-003, Sikker bruk av løfteutstyr er bransjestandarden for operasjon av løfteutstyr på norsk sokkel.

Kurset ”Sikker bruk av offshorekran” er bygget opp rundt NORSOK R-003 og er et viktig verktøy for å tilfredsstille myndighetenes krav om vedlikehold og verifikasjon av kompetanse innen sikker bruk av løfteutstyr.

Kurset fokuserer på god arbeidspraksis, samt å skape gode holdninger og sikkerhetsforståelse ved kranoperasjoner i henhold til NORSOK standard R-003.

Kurset gir en introduksjon til den nye versjonen av R-003 som ble lansert i 2017.

Dette kurset inneholder referanser til 2004 versjonen av R-003, men kurset i sin helhet vil bli oppdatert når ny versjon av R-003 blir lansert med oppdatert tillegg B.

Kurset inneholder:

-Introduksjon

-Ansvar og roller

-Planlegging og ledelse

-Kommunikasjon

-Forsyningsfartøy

-Lastbærer

-Kjemikalier

-Løft til og fra boredekk

-Bruk av styretau

-Løft av bore- og foringsrør

-Monterings- og demonteringsløft

-Løft av stilasemateriell og plank

-Blindkjøring

-Personløft

Presentation

This training course is about what an effective cyber security risk management should be. Its goal is not to address too many technical questions as the best technical expertise in the world won’t guarantee zero cyber risk. The course aims at providing your Company with a real battle plan: know the assets, know the enemies, organize accordingly and train the effectives. Although this will not be enough to avoid a cyber incident, the severity of the consequences of a cyber incident will depend on the company’s preparedness and ability to manage it.

Who the course is for?

The course ISM Code and Cyber Risk Management is aimed at anyone interested in understanding how an effective cyber security risk management should be. This may include Top Management of Shipping Companies, Ship Managers, Technical Superintendents, Ship Masters, Officers and Seafarers; Offshore Units Operators and Technical Staff, Shipyards Technical Staff; Surveyors; P&I and/or Insurance Inspectors; etc.

Objectives

On completion of the training, students will be able to:

Know what cyber security is, the main threats and their consequences.

Understand how to consider the cyber risks in the Safety Management System and how the ISM Code translated into cyber security.

Know the 12 cybersecurity commandments that will help implementing an efficient cyber risk management system.

Kurset gir en innføring i kjemikaliestyring, risikovurdering av helse i forbindelse med arbeid med kjemikaler. Kurset baserer seg på bruk av ChemiRisk som verktøy for risikovurdering og CHESS som elektronisk stoffkartotek. Kurset består av tre moduler (teori, stoffkartotek (CHESS) og bruk av ChemiRisk).

Kursinnhold

- Teori

- Stoffkartotek (CHESS)

- Bruk av ChemiRisk

Kurstilbyder: Proactima

Who is this course for?

This course is aimed at all personnel involved in operations involving the use of seals, particularly those who are expected to undertake related duties in the workplace.

Is previous experience required?

You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?

This course aims to provide an overview of the role and application of seals and gaskets

How will this course benefit my company?

To ensure you have an overview of the role and application of seals and gaskets

What standards are referred to in this course?

The course is made according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Kurset er kun tilgjengelig på engelsk.  

Dette kurset er kun tilgjengelig engelsk.

Who is this course for?
Process Operators and Lab Technicians

Is previous experience required?
You do not need prior knowledge or experience to complete this course and it is assumed that you are competent in your designated role

How will this course benefit me?
This course aims to provide an overview of the various types of process chemicals, their use and how they work.

Section 1: Basic Introduction to Chemistry
Section 2: Process Chemicals in the Oil and Gas Industry
Section 3: Identifying the Risks in the Use of Process Chemicals
Section 4: Managing Chemical usage

How will this course benefit my company?
By ensuring you have an overview of the various types of process chemicals, their use and how they work.

What standards are referred to in this course?
N/A

Is there an assessment?
Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Kurset dekker den teoretiske delen av dokumentert sikkerhetsopplæring som kreves for anhukere og signalgivere.

Kurset er også godt egnet som repetisjon for kranførere og annet personell som tidligere har gjennomført opplæring innen løfteinnretninger og løfteredskap.

Innholdet i kurset omhandler valg, kontroll og sikker bruk av de mest vanlige løfteredskap i bygg- og anlegg, industri, sjøfart og offshore.

Signalgivning, kommunikasjon og styring av last er sentrale emner i kurset.

Kurset forutsetter at det gjennomføres praktisk opplæring på aktuelt løfteredskap i tillegg.

Kurset inneholder følgende moduler:

• Løfteutstyr, ord og uttrykk

• Anhuking, tyngdepunkt, arbeidsvinkler og løftetabeller

• Fiberstropper

• Kjettingredskap

• Ståltaustropper

• Sjakler

• Øyebolter, øyemuttere og løfteører

• Signaler og tegn og styring av last

• Sikkerhetsregler

Hver modul inneholder øvingsoppgaver, og 8 av modulene har avsluttende test med 10 spørsmål i hver modul.

Who is this course for?

All personnel who are involved in offshore drilling.

Is previous experience required?

No previous experience is required to complete this course.

How will this course benefit me?

This course aims to provide an overview of well control and the systems used in the process and is based upon the International Well Control Forum (IWCF) Level 1 Syllabus.

How will this course benefit my company?

This course will benefit companies by ensuring personnel have an understanding of well control and the relevant systems.

What standards are referred to in this course?

No standards or regulations are referenced in this course.

Is there an assessment?

Yes

Hensikten med kurset er å introdusere kravene som gjelder til vedlikehold av overflatebehandling.

Etter fullført kurs skal brukeren kunne:
- Hva som menes med overflatebehandling
- Krav til overflatebehandling
- Mulige konsekvensene av å fjerne rust fra korrodert utstyr
- Ulike metoder for overflatebehandling
- Ulike teknikker for inspeksjon
- Tiltak som bør vurderes ved utførelse av overflatebehandling

Kurset er kun tilgjengelig på engelsk. 

Presentation

This training course provides a general overview of the SOLAS requirements concerning radio communications and the Global Maritime Distress and Safety System (GMDSS).

Objectives

On completion of the training, students will be able to:

Know the requirements concerning radio communication equipment on board ships and offshore units.

Understand the GMDSS functional requirements.

Understand the means required for GMDSS tests and drills on board.

Know the requirements for EPIRB, radio lifesaving appliances and sources of energy for radio communication equipment.

Program

Safety radio surveys and certification

GMDSS functional requirements

o Land and satellite communications

o Inmarsat

o Functional requirements while at sea

o Distress urgency and safety radio communications

o Sea areas

o Maintenance of radio installation

o Maintenance of satellite EPIRB

o Maritime safety information

GMDSS equipment

o Equipment to be provided on board

o Core installation

o Inmarsat EGC

o NAVTEX

o Satellite EPIRB and VHF EPIRB

o Search and Rescue Transponder (SART)

o Digital Selective Calling (DSC)

o Two-way VHF radio-telephone

Main, emergency and reserve sources of power

Automatic battery chargers

Uninterrupted power supply (UPS)

Certificate

On completion of the training program, the student will be awarded:

A Certificate of SOLAS Safety Radio, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of SOLAS Safety Radio is obtained after completion of the course and passing the online test.

Who is this course for?

Personnel requiring an awareness or understanding of the common safety methods when using scaffolding over the sea.

Is previous experience required?

You do not need prior knowledge or experience to complete this course.

How will this course benefit me?

This course aims to give an overview of requirements for safe scaffolding operations over sea.

How will this course benefit my company?

By ensuring you have an overview of the requirements for the safe use of scaffolding over the sea.

What standards are referred to in this course?

This course does not refer to specific legislation or standards but is written according to industry best practice.

Is there an assessment?

Once you have completed the course, you will be asked a series of questions to check your knowledge and understanding. These are based on the learning objectives for the course and have a pass mark of 80%.

Kurset er kun tilgjengelig på engelsk.